事实上，彩钢夹芯板的施工方法有很多。在施工过程中，我们可以选择一些合适的浇注方式，让施工效果可以更好。下面济南彩钢夹芯板厂就来说说彩钢夹芯板主要的浇筑方法。

In fact, there are many construction methods for color steel sandwich panels. In the construction process, we can choose some suitable pouring methods to make the construction effect better. Next, Jinan Color Steel Sandwich Panel Factory will talk about the main pouring methods of color steel sandwich panels.

1、彩钢夹芯板一次性浇筑法是将基座基础支撑面的混凝土一次性浇筑到结构高度。为保证承重面高度正确，先将混凝土浇筑到低于施工高度约20-30mm的位置，然后在施工高度上放置角钢或槽钢导架，从侧面将其高度调直，然后在导向架的基础上用水泥浆找平到设计水平。一次性浇筑工艺可以省去多次浇筑立柱底座的劳力，但钢柱的制作尺寸须非常准确。确保细石混凝土牢固地粘合在下面的混凝土上。

1. The one-time pouring method of color steel sandwich plate is to pour the concrete on the supporting surface of the foundation to the structural height at one time. In order to ensure the correct height of the bearing surface, first pour the concrete to a position about 20-30mm lower than the construction height, then place the angle steel or channel steel guide frame at the construction height, straighten its height from the side, and then level it to the design level with cement slurry on the basis of the guide frame. The one-time pouring process can save the labor of pouring the column base several times, but the manufacturing size of the steel column must be very accurate. Ensure that the fine aggregate concrete is firmly bonded to the concrete below.

2、彩钢夹芯板二次浇筑法是支撑柱基基础，二次浇筑混凝土至设计高度。浇筑比计划高度深约40-60mm的混凝土。待混凝土达到一定强度后，放置钢垫板并准确标定钢垫板高度，然后吊起钢柱。钢柱标定后，在柱基底板下浇筑细混凝土。二次浇筑法虽然涉及另一道工序，但钢柱容易修正，所以这种方法主要用于重型钢柱。

2. The secondary pouring method of color steel sandwich plate is to support the column foundation, and the secondary pouring concrete to the design height. Pour concrete about 40-60mm deeper than the planned height. After the concrete reaches a certain strength, place the steel base plate and accurately mark the height of the steel base plate, and then lift the steel column. After the steel column is calibrated, fine concrete shall be poured under the column base plate. Although the secondary pouring method involves another process, the steel column is easy to be corrected, so this method is mainly used for heavy steel columns.

彩钢夹芯板安装一般步骤分为三个部分，准备安装、执行安装和检查安装三个。这三个部分可以帮助我们解决很多的难题。在施工顺序上以及施工质量上都有一定的帮助。例如我们在进行幕墙板安装，采取的是活动脚手架的方式来进行。

The installation of color steel sandwich panel is generally divided into three parts, including preparation for installation, execution of installation and inspection of installation. These three parts can help us solve many problems. It is helpful in construction sequence and construction quality. For example, we are installing curtain wall panels in the form of movable scaffolding.

因此我们在保证相关施工脚手架承载力的范围内还需要注意到幕墙面与作业面以及轴线间距离的大小；另外我们还需要通过对比参考面，寻找出相应控制点间距以及位置并注意它的通视性；安装角的间距需要通过参考面来找出；对于它与控制标高水平差也是一个很重要的参数；后还要保持跟建筑物竖向保持一定距离。

Therefore, within the scope of ensuring the bearing capacity of relevant construction scaffolds, we should also pay attention to the distance between the curtain wall and the working surface and the axis; In addition, we need to find out the distance and position of corresponding control points and pay attention to its visibility by comparing the reference plane; The spacing of installation angle needs to be found out by reference plane; It is also a very important parameter for the level difference between it and the control elevation; After that, keep a certain distance from the building vertically.

以上是彩钢夹芯板的浇筑方法，我们可以使用以上两种方法来。在施工过程中，一定要小心谨慎，采用合适的施工工艺，只有采用合适的浇注方法，才能更好地完成施工。更多相关内容就来我们网站http://www.jnhscg.com进行咨询吧！

The above is the pouring method of color steel sandwich panel. We can use the above two methods. In the construction process, we must be careful and adopt appropriate construction technology. Only by adopting appropriate pouring methods can we better complete the construction. Come to our website for more relevant content http://www.jnhscg.com Consult!